aua668
About
- Username
- aua668
- Joined
- Visits
- 2,363
- Last Active
- Roles
- Member
Comments
-
Hi, Icing was not the problem as far as I remember. I will check the next time the ISOL valve as proposed and report back. Thanks for taking care. If you are talking about the ISOL valve do you mean the "Airframe Deice Air Isolation Valve"? …
-
Hi, The flight yesterday was done in LFSB (Justsim scenery): LFSB 181930Z 19006KT CAVOK 07/05 Q1025 NOSIG Bale-Mulhouse, France (LFSB) 47-36N 007-31E 271M Nov 18, 2020 - 02:30 PM EST / 2020.11.18 1930 UTC Wind: from the S (190 degrees) at…
-
Hi, Did just another test and this time the PFD altimeter on the left side was 400 ft ABOVE the correct value. The altimeter on the right side and the STBY altimeter showed the correct value. Then I closed the sim and started with the same fli…
-
Hi, Another airline operating the Q400 sets the bugs like this: Take-Off Landing: Rgds Reinhard
-
No - I am on 5.1 but there was no change compared to previous versions. Which timer have you set in the control panel? Rgds Reinhard
-
Hi, As you have obviously a lot of questions, please check the documents on this website: https://smartcockpit.com/plane/BOMBARDIER/DASH-8-400.html Furthermore there is a DOC folder in your aircraft directory, where you find excellent documen…
-
Hi, Here is an alternative, which is always working: http://majesticsoftware.com/mjc8q400/docs/SpeedCard_metric.pdf http://majesticsoftware.com/mjc8q400/docs/SpeedCard_imperial.pdf Rgds Reinhard
-
Hi, Maybe you check this conversation: http://majesticsoftware.com/forums/discussion/comment/3207 Rgds Reinhard
-
Hi, I also use the Q400 from FSX over all versions of P3D up to v5. And I can confirm, that steering was always working and there is no difference across all versions. So it must be on your side and it's not a bug of the Q400. You typically ha…
-
Hi, Rgds Reinhard
-
Hi, Have you checked Aviaworx? They run the CDU on a remote tablet or PC and they use a background image, which you could replace I assume. Rgds Reinhard
-
Hi, As the manual says: You have to reduce V1. There is nothing said about Vr/V2. It would also be not logical, that the speed, when the plane rotates and when it flies stable would change by a wet runway. Of course the speed, where you latest ca…
-
Hi, Another difference: I displayed the engine system page on the FO side. You obviously on the captain's side, as your display shows the PFCS below, while mine display shows the flaps, hydraulics, etc. Rgds Reinhard
-
Hi, Strange behavior. On my system Eng 2 and Eng 1 show the same values during start and increase synchronously (beside the small difference for Eng 2). But the values are definitely the same. You use the pop-up panel, while I showed a screenshot…
-
Hi, There are two engine configuration files: PW150A1.xml and PW150A2.xml There is a minor difference in the configuration file, which explains, why one engine shows 135 and the other 139: I assume, this should simulate, that no engine is…
-
Hi, I have checked this with P3Dv5 and with that version I don't see this behavior. FF of Eng 2 on the engine system page is the same as on EICAS and it starts immediately to raise when the engine is started. There is one strange thing: FF of …
-
Hi, With FSUIPC you can achieve this (and much more). Rgds Reinhard
-
Hi, Fine to hear. You are doing a great job. Thanks for sharing the pics. Rgds Reinhard
-
Hi, As I have written above, I was only able to use UDP connector 3 for sending/receiving. 4 to 9 should work (but maybe with the training version only): @aua668 said: Hi, One thing described in the documentation did not work for…
-
Hi, Maybe this document is helpful for understanding: osha.igs.net/~kiddbatt/DOCS/unsbs/UNS_OTM_2009.pdf Search for approach activation in the document. Rgds Reinhard
-
Hi, You have to use the XML interface for setting them. The variables are in the EFIS section. EFISdata_->ARCDUs[0].stby_freq_com[0] Like: 35775 for 135.775 EFISdata_->ARCDUs[0].stby_freq_com[1] Like: 35775 for 135.775 EFISdata_->A…
-
JP, I did now the same flight in P3Dv5 and everything worked fine. This doesn't help you with your problem. Rgds Reinhard
-
Hi JP, I am already on P3Dv5. But for reference I will try to fly this route. Rgds Reinhard
-
Hi, I did not yet fly this route but I had a similar behavior in the past in an area of Austria. When I approached Vienna on of the STARs, the sim crashed. Other STARs worked without any problem. The solution I found after a hint of another us…
-
Hi, Arduino obviously send the ASCII hex values for the single digits: 32 = 2 31 = 1 20 = blank 35 = 5 32 = 2 20 = blank So you are sending the datagram (21 52 ...) but Arduino converts each digit into the ASCII hex representation. Rg…
-
Douglas, I am away from my sim for two weeks. So please standby for an answer. Rgds Reinhard
-
Hi, Just for clarification: Did you install both mods? There is one for the VC and one for the exterior. Works here with P3D v5 perfectly - many thanks for this improvement. Rgds Reinhard
-
Hi, If you have the PRO version: They had linked the PILOT version by error to my account although I own the PRO version. Now it's corrected. Check if you have downloaded the wrong version and reload. Rgds Reinhard
-
Hi, Maybe you check this thread: majesticsoftware.com/forums/discussion/239/system-panel-on-remote-pc-showing-only-white-rectangle I had the same problem on a second PC- I solved it by "brute force". Rgds Reinhard