kroswynd
About
- Username
- kroswynd
- Joined
- Visits
- 6,379
- Last Active
- Roles
- Member, Administrator, Moderator
- Invited by
- Boss
Comments
-
Hello, Let's start by providing as many details as you can, unfortunately we'll need some background information to assist us in trying to determine what the cause of your issue may be. * System specs: * OS: * Simulator platform: * …
-
http://majesticsoftware.com/forums/discussion/94/attention-flight-sim-store-customers/p1?new=1
-
@CaptainNorton Ckyliu is correct in his explanation.... What you may have heard is incorrect. Cheers
-
Unless you have other finctions bound to the default P3D assignments - CLT+E+2 for the cargo door and CTRL+E+3 for the rear pax door should work as assigned. however some users were having issues initiating this sequence - as it does however rely o…
-
Good to hear
-
Are you ensuring that Both of you have the same mode selected and you have clicked on APPLY.... THEN.... reloaded the aircraft? (do not reload the simulator... Just the Q400) Sounds silly but I have to ask as many people do miss this critical …
-
Kindly pay close attention of the verbiage in how to attain an upgrade for the 64bit Q400 https://www.justflight.com/articles/majestic-software-dash-8-q400-new-p3d-v4-editions It is possible to upgrade, at a discounted price, from the PILOT to t…
-
Simply go to the vendor from which you purchased the Q400 and purchase the 64bit upgrade, since you already own the PRO Edition. Cheers
-
Ok I am closing this as having two posts with the same data ends up causing more confusion. Cheers
-
Thank you for bringing this to our attention. I was waiting to see how much feedback would come up from this thread, although not much it enough for us to start digging a bit deeper into whether its a Dash/Navigraph issue.
-
Sounds like you have not configured the CPAN Shared Cockpit mode correctly: Flying Mode is the commonly used mode if only two pilots are sharing a flight deck
-
If you are interested in the PRO Edition simply go to the vendor from which you purchased the PILOT Edition and purchase the PRO version (32 bit) and then purchase the PRO 64 bit upgrade. Be sure to read the instructions on the vendors website from…
-
Well there are several responses that one could provide based on your vent but we appreciate your venting. Having a favorite aircraft developer is no big deal and you are free to express yourself, however I would use caution in how you go about doi…
-
Please be sure to uninstall, then reinstall the Q400 using Administrative Rights by right clicking on the installer. Also you may want to disable your anti-virus software before commencing the installation. Cheers
-
Kindly write to us via email to our Support department to discuss the issue
-
The "ini" folder which is located in you mjc8q400 folder will contain the following lines:? [INTERFACE] ; GENERAL SUPPORT OF THE INTERFACES JOYSTICK_INTERFACE =1 ASN_INTERFACE=1 WXAR_INTERFACE=0 ASN_INTERFACE=1: enables the uses of Activ…
-
As always...stunning piece of work
-
There are 2 switches for weather radar, one is for Active Sky and the other is for REX products which is still a work in progress.
-
A full install should not be required. Have look in your mjc84.ini at the beginning there should be a line WXAR=1. Change that to 0
-
Are you by any chance running sky force as your weather engine generator?
-
@Radial9 The response from Master_Warning was on behalf of the MJC team. @ckyliu.... Thanks for break down the of the route structure for I have not flown this for a while. There is a second tutorial which was compiled and should be avail…
-
Unfortunately the Q400 does not pair well with the Saitek instrument panels due to our flight dynamic modeling
-
-
There should be a slider allowing one to increase/decrease the sensitivity which is located next to the elevator trim binding in the Controls section of P3D. If you are unfamiliar with this you may have to do some research on how to do this but it …
-
The aircraft.cfg may or may not be the issue, but it may be more beneficial if you provide a detailed explanation on how you are attempting to setup your Q400 regarding the installation. Cheers
-
@nigelgrant said: put the computer into its highest speed (hit R+++++++) then the repair will only take a minute! Nigel Vancouver LOL....well that is one way to do it
-
ELEVATOR TRIM can be set via button or key assignments under the Controls tab in P3D
-
Hello, The issue you explain usually is the result of a protection problem. Lets start by un-installing the aircraft and re-installing using Admin rights by right clicking on the installer. Be sure to disable your anti-virus for the installatio…
-
In real life one can not fix a tyre from a FMS (not MCDU) There are two ways in which this can be solved 1. Reloading the aircraft (not the sim) 2. Waiting twenty minutes for the repair to be completed....(in real life it takes about 45 min …
-
Not knowing the specifics of your assignments, on e can only assume that you are using the FSX/P3D method for trim, and if so you may want to try adjusting the trim sensitivity slider in the controls section. If you are using FSUIPC or other util…