kroswynd
About
- Username
- kroswynd
- Joined
- Visits
- 6,379
- Last Active
- Roles
- Member, Administrator, Moderator
- Invited by
- Boss
Comments
-
JP, How goes it? The behavior being exhibited has been a long time nuisance within the FSX and P3D platform where by the aircraft would initiate a momentary turn in the opposite direction before proceeding to its intended path. The Boss was abl…
-
I suspect you are referring to creating a null zone for the respective lever axis. Unless the device has noise or you are trying create a point wherein the axis moves within a certain range, why don't you try make the null zone as low as possible, …
-
Double posting is not necessary..... Ok, your condition levers both going to fuel cut off has norhibg to do with the failure scripting or functionality. Have you verified All of your input device axii as it sounds from your explanation tha…
-
1. As the previous poster mentioned a pic of your wt and balance page from the CPAN may help us in better understanding the issue. 2. During your issue are you able to look at the pitch trim indicator to see its position. 3. The tiller …
-
Ok, your condition levers both going to fuel cut off has norhibg to do with the failure scripting or functionality. Have you verified All of your input device axii as it sounds from your explanation that this bmay be the contributing factor in …
-
We are not changing anying outside of what is already in place with the implementation of the new installer at this time. Cheers
-
OK this stops here!! Regardless of whether it may be for developers or not, if users find its usefulness for other troubleshooting issues the more the merrier. It serves purposes for many. @picard Regarding the MJC side, this error will not…
-
Not an issue I recall seeing over the few years that the Q400 has been in existence. I asked in my previous post if you are able to move the condition levers (CTRL + F2 or F3)?
-
You can simply ignore this file as it does not pertain to the version which you own. What are the issues you have with the pitch trim, or there are no issues?
-
Could you provide more information as to what simulator you are using? Have you tried using the key commands to execute the manipulation of the condition levers?
-
we had to implement it this way to ensure that all data from the CPAN is transferred correctly. it could change down the road, but at this time no planned changes
-
We certainly were, but we had higher priorities this time around. The aircraft works out of the box but requires some tweaking, so I'll make an official announcement when all things are in place
-
@SteveS The issue your describe particular to a Win10 update is not a common one. User normally report protection issues similar to that of not having the gears visible or indications on the ED being garbled, or the propellers showing a flat pit…
-
We will make announcement when it is. Cheers
-
A bit stumped by this one. May I ask you to un-install again and re-install using Administrator Rights as you have previously done. Be sure to load one of the default aircraft within the P3D v4.5 platform (mooney, f22, etc), and then load the Q400.…
-
This is not a very common issue although similar has been experienced before. Previous attempts to rectify this issue involved usually involved updating graphic drivers. Have you installed the aircraft to its suggested installation path? Keep u…
-
Good to hear you are back on track. Cheers
-
It should work
-
The PRO Edition by default comes with the Electrical and Hydraulic Systems in the SYSPAN for failures. One is however able to create their own failures via the implementation of additional scripts. We have provided a guide to assist in doing so. …
-
There are odd occasions where that can happen. We have encountered it a few times during extensive testing, but have seen it more often when a complex aircraft was selected prior to loading the Q400. For best results, attempt to load a default air…
-
Looks like you may have missed a step. 1. Select the panel state of choice. 2. Click APPLY (this may be the step you are missing) 3. Re-load the aircraft Keep us posted
-
Hello Christian, Modifying the panels on your own will be down at your risk, as we will not offer support for any changes made to any aspect of the model. Cheers
-
McAfee and other anti-virus software packages have been known to bottleneck or prevent the shared cockpit functionality for some users. Did you try to run the Q400 internal SC without himachi after removing McAfee? Glad to hear that you got it…
-
Thank you bringing this to our attention, have not used GSX for a while but will have to do some testing on this to verify. Cheers
-
Mostly yes primarily for the TRAINING EDITION. However one can create their own script for engine fires/failures etc. Cheers
-
Kindly be specific regarding you issue. 1. Gear handle not moving 2. Handle moving but gear not retracting Could you consider investigating? I would think this is what we have been doing for the past several months. This issue …
-
You would have better luck getting an instant response using a Facebook group. As users reading your post may not be available the same time that you are, but it does hurt to try. Cheers
-
We do not sell the Q00 directly from our website. Can you verify who the vendor is from which you Purchased the Q400 so that we can proceed with your issue. Cheers.
-
some images may help us, or better yet a small video clip of how you are attempting to operate the weather radar. Cheers
-
http://majesticsoftware.com/forums/discussion/704/the-majestic-2020-roadmap#latest